|
|
|
1
|
2
|
3
|
4
|
5
|
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
|
27
|
28
|
29
|
30
|
|
|
|
|
|
71 registered members (murf205, HHSyelper, Fattyfireplug, Hoytdad10, USeeMSpurs, sw1002, HBWALKER14, drakehunter_03, GomerPyle, Fishbones, Epalm88, Mulcher, AU338MAG, BrentsFX4, Okatuppa, jmj120, BearBranch, Conc49, outdoorguy88, CreekCrosser, sidehitter, Bread, Mbrock, jaredhunts, Overland, Cynical, Tree Dweller, mw2015, bambam32, Ray_Coon, Pwyse, CKyleC, BD, Mansfield, BamaPlowboy, Canterberry, Tall Dog, SC53, Gobstopper, Dean, treemydog, BentBarrel, rkt, janiemae, Bgood, Obsession, hootn, eclipse829, jprice, Paint Rock 00, CrappieMan, bhammedic84, HappyHunter, NotsoBright, Hunter454, goodman_hunter, mzzy, Driveby, RCHRR, coldtrail, dave260rem!, Bruno, JLMiller, Peach, bamaeyedoc, Flyliner, 5 invisible),
805
guests, and 0
spiders. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
Hope y’all can give me some input
#2857078
07/21/19 11:23 AM
07/21/19 11:23 AM
|
Joined: Dec 2017
Posts: 65
Tuscaloosa Al
Dalton
OP
Misser of Roosted Doves
|
OP
Misser of Roosted Doves
Joined: Dec 2017
Posts: 65
Tuscaloosa Al
|
This is going to be a very specific question that I’m sure not many people have dealt with. I’ve searches the internet up and down and can not find an answer so I’m hoping someone here can give me some insight. I have a 2006 Toyota Tacoma with what i have narrowed down to be the TRD quickshifter in it. I bought the truck a few weeks ago so i didn’t install it. But when I’m driving i get a buzzing sound from the shifter and if i lift the shifter up and take the slack out of it it stops. This morning i took the shifter out thinking it was the lever bushings but figured out that it’s actually a 2 piece shifter with the top piece being pretty much a hollow tube, that’s the part the shift ball is attached too. With all that being said i can wiggle the shifter and the hollow tub will wiggle back and forth but the actually shifter rod that goes into the trans is tight as can be so it’s not slack in the trans. Apparently a bushing is worn out in the tube but i cant for the life of me find replacement bushings online nor can i figure out how to get it apart. Has anyone else experienced this and fixed it? I apologize if that sounds confusing lol. If need be you can message me your number and i can send you a video of what I’m trying to explain. Thanks in advance!
It’s better to keep your mouth shut and have people think you’re and idiot, than to open your mouth and remove all doubt
|
|
|
Re: Hope y’all can give me some input
[Re: gundoc]
#2857100
07/21/19 12:05 PM
07/21/19 12:05 PM
|
Joined: Dec 2017
Posts: 65
Tuscaloosa Al
Dalton
OP
Misser of Roosted Doves
|
OP
Misser of Roosted Doves
Joined: Dec 2017
Posts: 65
Tuscaloosa Al
|
I’m not far away from it!!
It’s better to keep your mouth shut and have people think you’re and idiot, than to open your mouth and remove all doubt
|
|
|
Re: Hope y’all can give me some input
[Re: Dalton]
#2857109
07/21/19 12:28 PM
07/21/19 12:28 PM
|
Joined: Aug 2001
Posts: 72,613
Luverne, AL
Skinny
GUVNER
|
GUVNER
Joined: Aug 2001
Posts: 72,613
Luverne, AL
|
Happy Birthday! and take that truck back to the lot. You bought a lemon.
"Never Trust Government" -- Smart people.
"The Great thing we should Fear and the Weird Thing we Trust is Elon Musk" -- Me
"You can be broke but you cant be poor." -- Ruthie-May Webster
|
|
|
Re: Hope y’all can give me some input
[Re: Dalton]
#2857162
07/21/19 02:12 PM
07/21/19 02:12 PM
|
Joined: Dec 2002
Posts: 12,641
Kennedy, al
globe
Booner
|
Booner
Joined: Dec 2002
Posts: 12,641
Kennedy, al
|
I’ve replaced the knuckle on the old shifters several times to tighten them up, but idk about the new ones and buzzing sounds??? So there’s wires hooked up to the shifter in a manual?
Everything woke turns to shucks
|
|
|
Re: Hope y’all can give me some input
[Re: Dalton]
#2857266
07/21/19 05:13 PM
07/21/19 05:13 PM
|
Joined: Oct 2008
Posts: 8,210
In front of my lathe
gundoc
14 point
|
14 point
Joined: Oct 2008
Posts: 8,210
In front of my lathe
|
To add to Dalton's description, it almost sounds like gear teeth spinning a barely rubbing something making a faint buzzing sound, but if you put just light pressure on the shifter, it quits.
There are two types of gun enthusiasts ... Those who have been F#CKED by PTG and those who will be!
~ unknown
|
|
|
Re: Hope y’all can give me some input
[Re: Dalton]
#2857309
07/21/19 05:58 PM
07/21/19 05:58 PM
|
Joined: Dec 2017
Posts: 65
Tuscaloosa Al
Dalton
OP
Misser of Roosted Doves
|
OP
Misser of Roosted Doves
Joined: Dec 2017
Posts: 65
Tuscaloosa Al
|
From what I’ve narrowed down i believe the buzzing it’s the metal shift rod coming out of the transmission going into the hollow tube touching the side and it’s just metal against metal
It’s better to keep your mouth shut and have people think you’re and idiot, than to open your mouth and remove all doubt
|
|
|
|
