|
|
|
|
Peanuts
by Jwoods32. 11/21/24 03:39 PM
|
|
|
|
|
|
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
|
124 registered members (bamamed1, Auburn1716, remlap, BCLC, Sheepdog, fillmore, Beer Belly, gatorbait154, Sasquatch Lives, rkt, Exhoosier, Driveby, Gunner211, jtillery, georgiaboy1970, trlrdrdave, Zzzfog, G/H, HURRICANE, 2walnuts, jake5050, russellb, timberwolfe, Bustinbeards, Sqzpla, Garndawg, chill, Longtine, Etyson, canine933, GoldenEagle, wareagle22, Overland, General, Butchman205, desertdog, MS_Hunter, Jmfire722, BamaGuitarDude, BamaBoHunter, metalmuncher, Hoytdad10, El_Matador, biglmbass, bug54, znix123, bambam32, DHW, Holcomb, garyc, therealhojo, MGrubber, apolloslade, AustinC, 1faststang, canvasback, doc bar, jwalker77, woodduck, rickyh_2, RidgeRanger, capehorn24, Pipedream, SC53, scrubbuck, GmeHunter, Cactus_buck, Scott4Hunting, jericward, Whild_Bill, Narrow Gap, low wall, YellaLineHunter, Cutem, Reptar, DGAMBLER, Redman3, 700ltr308, Chiller, zwick, AU7MM08, Turkeyneck78, cartervj, TexasHuntress, OutdoorsAL, Bmyers142, jhardy, dave260rem!, Bruno, jprice, dawgdr, scrape, outdoorguy88, johnv, Gulfcoast, T-hatchie, TSB, CB5121, TurkeyJoe, rhino21, TDog93, 3006bullet, Atoler, twaldrop4, Paint Rock 00, Grokamole, joe sixpack, Jwoods32, sawdust, jlbuc10, deerman24, JCL, Raspy, fish_blackbass, 10 invisible),
813
guests, and 0
spiders. |
Key:
Admin,
Global Mod,
Mod
|
|
|
Re: ? Accubond guys
[Re: BCLC]
#4221774
11/01/24 11:37 AM
11/01/24 11:37 AM
|
Joined: Feb 2007
Posts: 20,768 colbert county
cartervj
Freak of Nature
|
Freak of Nature
Joined: Feb 2007
Posts: 20,768
colbert county
|
The astric means the most accurate load tested. Those are the powders I had on hand and that is the reason I loaded them the way I did. It means it was the most accurate load tested in the gun at the Nosler factory and that data may be 30 years old. It has very little correlation with what may be the most accurate load in your gun. When looking at the data above, I'm going to start with the powder which I have in my stock, has the most velocity potential and is close to 100% case fill. I'll try that powder with a load close to max and run tests with 3 or 4 seating depths to see which gives the best accuracy. After determining the best OAL, then I'll adjust the powder charge for velocity and accuracy. This ^^^^
“Socialism only works in two places: Heaven where they don't need it and hell where they already have it.” ― Ronald Reagan
|
|
|
|